Ceramic Polymers

  • Application consistency: liquid
  • Reference Number: 98/108
  • Product Applicability: it is a product formulated with epoxy phenol novolac modified, 100 % solid, bi component containing his load formulation of fine ceramics of high density and mineral fillers, and applied with a brush for protection of surfaces subject to wear by erosion, especially acids. In the protection and recovery tanks, pipes, floors, foundations, these equipment which are in contact with sulfuric acid 98%.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 93°C (199°F)
  • Application consistency: from pasty to liquid
  • Reference Number: 80/800 and 81/801
  • Product Applicability: It has in its composition self-lubricating characteristics and resistance to abrasion. It is indicated in the recovery of shafts, seat of pumps rings, bearing seats, lathers, milling machines, planers, pump casings, rotors, bronze bushes, gutters and heat exchanger.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 120°C (248°F)
  • Application consistency: pasty
  • Reference Number: 85/805
  • Product Applicability: This product is indicated in the recovery of equipment in pulp and paper mills, fiber tanks, mass tanks, water tanks, including drinking water, etc. It is also recommended in the marine industry, such as repairs of ship hull, concrete structures, etc.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 75°C (167°F)
  • Application consistency: from pasty to liquid
  • Reference Number: 90/900 and 91/901
  • Product Applicability: It has in its composition molybdenum disulphide, which gives excellent characteristics of lubrication. It is used for rebuilding lathes, planers, milling machines, cylinder liners, hydraulic pistons and bronze bushes.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 120°C (248°F)
  • Application consistency: from pasty to liquid
  • Reference Number: 100/1000 and 101/1001
  • Product Applicability: Suitable for rebuilding and protecting surfaces subject to abrasion, erosion and chemical attack such as wear caused by alcohol, pump casings, rotors and fermentation vats. It is also indicated on flanges, fans, heat exchangers, water tanks, tanks, vessels. After application, the finishing surface becomes smooth, reducing friction and wear by turbulence.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 170°C (338°F)
  • Application consistency: from pasty to liquid
  • Reference Number: 120/1020 and 121/1021
  • Product Applicability: It has excellent chemical resistance. It is suitable for coatings in rotors and shells of pumps, tanks, water boxes, flanges, fans, heat exchangers and vacuum forming models.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 170°C (338°F)
  • Application consistency: from pasty to liquid
  • Reference Number: 120/1020 and 121/1021
  • Product Applicability: It has excellent chemical resistance. It is suitable for coatings in rotors and shells of pumps, tanks, water boxes, flanges, fans, heat exchangers and vacuum forming models.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 170°C (338°F)
  • Application consistency: pasty
  • Reference Number: 135/1035
  • Product Applicability: It is a bi-component modified epoxy resin, 100% solid, containing in its formulation silicon carbide fillers. It has large and thick grains. It is resistant against abrasions and severe cavitations. The minimum coating layer thickness is 2,5mm. It is indicated to recover damaged pieces and to protect of new equipment, such as pumps, cyclones and pipeline curves.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 120°C (248°F)
  • Application consistency: pasty
  • Reference Number: 140/1040
  • Product Applicability: It has high resistance to severe abrasion, wear caused by slip and impact and the minimum coating layer is 6 mm. Suitable for protecting, repairing and rebuilding curves of pipes, and pumps damaged by coal.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 120°C (248°F)
  • Application consistency: pasty
  • Reference Number: 145/1045
  • Product Applicability: It has high resistance to severe abrasion and wear caused by slip and impact and the minimum coating layer is 6 mm. Suitable for protecting, repairing and rebuilding pulverisers and coal crushers.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 120°C (248°F)
  • Application consistency: pasty
  • Reference Number: 150/1050
  • Product Applicability: It has high resistance to severe abrasion and wear. The product is extremely hard due its formulation and the minimum coating layer is 6 mm. Suitable for protecting, repairing and rebuilding mud pumps, chip boxes and damages caused by sand and coal.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 120°C (248°F)
  • Application consistency: pasty
  • Reference Number: 160/1060
  • Product Applicability: It has high resistance to severe abrasion and wear caused by slip and impact and the minimum coating layer is 6 mm. This product has Kevlar on his formulation, so it is extremely resistant to abrasion and chemical products. Suitable for protecting, repairing and rebuilding pipeline curves, housings, exhaust fans, gutters, water tanks, cyclones, crushers, sprayers, mud pumps and chip boxes.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 230°C (446°F)
  • Application consistency: liquid
  • Reference Number: 171/1071
  • Product Applicability: This product has a great surface hardness and great resistance to abrasion and erosion. Suitable for coatings and uses in mud pumps, water treatment, centrifugal pumps, power plants, pulp and paper mills, mining, chemical plants and alcohol mills.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 120°C (248°F)
  • Application consistency: liquid
  • Reference Number: 181/1081
  • Product Applicability: It is a bi-component polymer resin, 100% solid, containing in its formulation silicon mineral fillers, modifiers and metal fillers. This product endures working temperatures up to 200°C.
  • Working Time (Partly Cured): 24h
  • Temperature Resistance: 200°C (392°F)